|
01-17-2020, 09:38 PM
|
#1
|
Junior Member
Brand: Thor Motor Coach
State: Florida
Posts: 13
THOR #16612
|
idok
Having difficulty adjusting (locking in upright position)the table in the dinette of the Thor Synergy. Anyone familiar with this?Idok.
__________________
|
|
|
01-17-2020, 10:29 PM
|
#2
|
Senior Member
Brand: Thor Motor Coach
Model: Freedom Elite 29fe
State: Florida
Posts: 700
THOR #4656
|
Suggest a more meaningful title. You might attract some helpful answers.
__________________
Making a smooth transition to senility for over 70 years
2017 Freedom Elite 29fe
2015 Jeep Wrangler Toad
|
|
|
01-18-2020, 12:17 AM
|
#3
|
I Think We're Lost!
Brand: Still Looking
Model: Tiffin Wayfarer 24 BW
State: New York
Posts: 22,195
THOR #8860
|
... But welcome to the Forum, and I hope that someone has the right answer for you!
__________________
"What: me worry?"
Good Sam Member 843599689
Current coach: Tiffin Wayfarer 24 BW
|
|
|
01-18-2020, 01:46 AM
|
#4
|
Senior Member
Brand: Thor Motor Coach
Model: Miramar 37.1
State: California
Posts: 2,497
THOR #12698
|
If it is like the one in my Siesta, the lever underneath must fit into the groove on the table bracket. I had to have mine adjusted to lock it in the upright position otherwise it would push down when pressure was applied to it.
Paul
__________________
|
|
|
01-18-2020, 03:37 AM
|
#5
|
Junior Member
Brand: Thor Motor Coach
State: Florida
Posts: 13
THOR #16612
|
I think I’ll have to do the same,
Thank you
__________________
|
|
|
01-18-2020, 03:09 PM
|
#6
|
Member
Brand: Thor Motor Coach
Model: Windsport 29M
State: Nevada
Posts: 70
THOR #11264
|
Table lock issue
Quote:
Originally Posted by Idok
Having difficulty adjusting (locking in upright position)the table in the dinette of the Thor Synergy. Anyone familiar with this?Idok.
|
Idok,
I have a 17 WindSport and had the same issue. Under the table looking towards the outside, mine has 2 holes to choose from to bolt the table extension too. I just changed holes and it locks fine now.
Hope yours is similar
__________________
|
|
|
01-18-2020, 03:21 PM
|
#7
|
Senior Member
Brand: Thor Motor Coach
Model: challenger 37FH
State: Delaware
Posts: 696
THOR #13399
|
Try pushing up bottom middle of table while pushing up handle at the same time .
__________________
|
|
|
01-18-2020, 04:35 PM
|
#8
|
Senior Member
Brand: Thor Motor Coach
Model: 32.1 ACE
State: Texas
Posts: 126
THOR #14323
|
Quote:
Originally Posted by Idok
I think I’ll have to do the same,
Thank you
|
Had same problem, unscrew, reposition & viola.
__________________
|
|
|
01-19-2020, 12:29 PM
|
#9
|
Junior Member
Brand: Thor Motor Coach
State: Florida
Posts: 13
THOR #16612
|
I’m going to take a pic and send it in,. It’s a little different configuration.
Thank you for your response.
idok
__________________
|
|
|
01-26-2020, 02:17 AM
|
#10
|
Member
Brand: Still Looking
Model: Newmar Ventana LE
State: Tennessee
Posts: 77
THOR #16834
|
Don't know if this helps: On our Citation (similar to Synergy), the table support is post with a metal tab that screws in and out of the end. The tab fits in a slot in one of the 2 floor plates, then you turn it clockwise (usually about 1/2-3/4 turn) until it is good and snug. If that metal tab gets screwed in to the end of the post too far then it won't catch and lock in the floor plate. Likewise, if it's too far out, then you can't get it to tighten.
__________________
|
|
|
01-26-2020, 03:17 AM
|
#11
|
Junior Member
Brand: Thor Motor Coach
State: Florida
Posts: 13
THOR #16612
|
Thanks Mr Goodbar,
I’m going to look at again and see if that’s the case.
__________________
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|
All times are GMT. The time now is 02:53 PM.