Cup holder solution.

[Hoser123]

2018 Thor 37rb class A. I finally figured out a solution to the lousy cup holders in my RV. It is a product called squeak Swigzy. it is a cup holder with an adjustable base. It fits into your cup holders in the basics pans to lock it securely in place. I just got mine through the mail and tried it it works great.

[Bob Denman]

http://www.thorforums.com/forums/att...1&d=1578942390

[Alex Morgan]

Till now i am looking for the better solution because up to get feedback from many source not feeling confident.

[ducksface]

There s a post on this forum, somewhere, explaining that a 3"to 4" abs pipe adapter works perfectly.

Abs does and pvc doesn't, or vice versa.

Maybe someone can find the thread/post.

[The Gritz Carlton]

Any cup holder is better than mine...not a single one up front. The wife has to hold my cocktails when I drive.

[Bob Denman]

All three of them at once?

http://www.thorforums.com/forums/att...1&d=1578956368

[Cwray]

[QUOTE=Bob Denman;219428] All three of them at once?

Sure! First wife in the passenger seat, the other two wives on the couch behind her.


I say “pics, or it didn’t happen”.

[The Gritz Carlton]

[QUOTE=Cwray;224283]

Originally Posted by Bob Denman

All three of them at once?

Sure! First wife in the passenger seat, the other two wives on the couch behind her.


I say “pics, or it didn’t happen”.

You musta seen me at a rest area somewhere!!!

[HaRVey]

I used the white pvc 3" caps and then removed the stock holders, using a dremmel with ~1/4" sanding drum to cut the bottom out (use the small outside bottom of the cup holder as a guide for the sanding drum). This leaves a net opening that will fit the pvc cap snug. I then used black abs pipe glue to bond the cap to the holder and paint the white cap inside with satin black.
The result is a holder that cups or bottles fit perfectly and you can't tell it's not stock (except that it works!)
The 3" black abs caps are too thick so the OD is larger than you can open the stock cup holder base to fit, nor will it fit in the factory opening.

[Yvonnemarc]

I found these cups fit perfect including the handle part.

[LAEN]

My drink holder needs to be a bit tighter because every time I slam on the brakes I spill my beer

[upnyfolks]

3" DWV couplers fit perfectly, and you can notch them to accommodate a handle if needed.

[halfprice]

As you can see I use these in every cup holder

Jerry

[AAL787]

A pony keg squeezes nicely between the seat and table. Just drink from the tap. No cup holder needed.

[Yaktop]

Originally Posted by Hoser123

2018 Thor 37rb class A. I finally figured out a solution to the lousy cup holders in my RV. It is a product called squeak Swigzy. it is a cup holder with an adjustable base. It fits into your cup holders in the basics pans to lock it securely in place. I just got mine through the mail and tried it it works great.Attachment 22184

Expensive buggers

[Ejohn2317]

Swigzy Car Cup Holder Expander Adapter with Adjustable Base - Rubber Tabs Hold Most 32 - 40 oz Bottles and Large Cups
Amazon's
Choice
for "car cup holder expander"

[Lin S]

I take a koozie cut it in half and slide it into the bottom of my travel cup or bottle water, fits into the cup holder fine for me. And it stays upright. I am a koozie fanatic.

[Pete'sMH]

Originally Posted by Lin S

I take a koozie cut it in half and slide it into the bottom of my travel cup or bottle water, fits into the cup holder fine for me. And it stays upright. I am a koozie fanatic.

Now that is a dandy idea!

[Hoser123]

Originally Posted by HaRVey

I used the white pvc 3" caps and then removed the stock holders, using a dremmel with ~1/4" sanding drum to cut the bottom out (use the small outside bottom of the cup holder as a guide for the sanding drum). This leaves a net opening that will fit the pvc cap snug. I then used black abs pipe glue to bond the cap to the holder and paint the white cap inside with satin black.
The result is a holder that cups or bottles fit perfectly and you can't tell it's not stock (except that it works!)
The 3" black abs caps are too thick so the OD is larger than you can open the stock cup holder base to fit, nor will it fit in the factory opening.

How about some pics.

[Hoser123]

Originally Posted by Pete'sMH

Now that is a dandy idea!

Also keeps your drink cool. Thumb